Removable Insulation Jackets for Contractors: Buy Instead of Build

If you run an insulation crew and need removable jackets for valves, flanges, strainers or pump casings, you can buy them built to your measurements instead of fabricating them in your own shop. All Temp Soft Covers has manufactured custom removable insulation covers in Blaine, Washington, since 2015. We ship nationwide, including Alaska. We manufacture and ship only; we never install, so we are never bidding against you for the labor.

Why contractors stop sewing their own jackets

Most mechanical insulation shops are set up for pipe covering, metal jacketing and board, not for cutting and sewing soft covers. A single valve jacket means patterning, cutting cloth and insulation, sewing, adding closures, and test-fitting. Every hour a journeyman spends at a sewing table is an hour he isn't on the job.

Buying jackets lets you:

• Quote the job on installed labor and keep your crew in the field

• Skip buying and maintaining sewing equipment and roll stock you only use a few times a year

• Hand the owner removable covers that can come off for maintenance and go back on, instead of fixed insulation that gets cut out and thrown away

What we make for contractors

We build each cover to the measurements, drawings or photos you send. Typical contractor orders include:

• Valve and flange insulation jackets for gate, globe, check and control valves, with the stem and handwheel left out of the cover

• Strainer, steam trap and expansion joint covers

• Removable pipe insulation jackets for elbows, tees and short spool pieces where fixed insulation keeps getting damaged

• Pump casing and volute covers

• Exhaust blankets for generators and engines

One-off covers and full valve lists are both fine. If you have a mixed list from a walkdown, send it as is and we will work through it with you.

The materials and ratings you can put in your submittal

Every cover uses the same two-layer build:

• Inner insulation: 1,000°F continuous / 1,200°F max

• Gray outer cloth: 450°F continuous / 500°F max

The inner insulation does the thermal work against the hot surface. The gray outer cloth is the face you see and handle. If your spec calls for a particular material, thickness or standard, send it with your request and we will tell you plainly whether we can meet it before you commit.

How ordering works from anywhere in the US

1. Send the list. Measurements, a drawing or clear photos with a tape measure in the shot all work. Our measuring guide shows which dimensions matter for each part.

2. We review it with you. We go over anything unclear by phone or video, so nobody guesses at a bolt circle or a bonnet height.

3. You get a quote. Pricing is competitive, and the quote is free.

4. We build and ship. Small projects ship in up to 2 weeks. Larger orders take 3–6 weeks. Covers ship to your shop or straight to the jobsite.

5. Your crew installs. Each cover is made to fit the part it was measured for, so installation is fit and fasten, not cut and patch.

Tips for a clean first order

• Tag each valve or fitting with an ID and use the same ID on your measurement sheet, so every cover can be matched to its spot when the box is opened.

• Note anything that has to stay accessible, such as gauges, drains, actuators or nameplates.

• Tell us the operating temperature and whether the equipment is indoors, outdoors or in a wet area.

• If you are bidding a job, ask for a budget quote from your takeoff. You can firm up measurements after award.

Read more about who we are and how we work with buyers in every state on our nationwide manufacturing page.

FAQ

Do you install the jackets? No. We manufacture and ship only. Your crew or the owner's maintenance team installs, which is why contractors can send us work without worrying about us going after the installation.

Can you work from photos instead of a site visit? Yes. Most orders come from measurements and photos. We follow up by phone or video when a dimension needs checking.

Is there a minimum order? Single covers are welcome, and so are long valve lists. Turnaround is up to 2 weeks for small projects and 3–6 weeks for larger ones.

About All Temp Soft Covers

All Temp Soft Covers is a custom manufacturer of removable insulation covers based at 7460 Clamdigger Dr, Blaine, WA 98230, founded in 2015 and owned by Philip Sanders. Insulation contractors, mechanical contractors and plant maintenance teams anywhere in the country can order from us. We manufacture and ship only, to any state including Alaska, and we don't do installation.

Get a free quote

Custom-made removable insulation covers at competitive prices, manufactured to customer specifications and shipped nationwide. Send your list, photos or drawings through our free quote page, call 360-383-6857, or email info@alltempsoftcovers.com.