top of page

When Insulation Has to Come Off: Washington Energy Code and Coast Guard Exhaust Rules

Writer: alltempsoftcovers
alltempsoftcovers
11 minutes ago
6 min read


All Temp Soft Covers, Blaine, WA.


Two different rulebooks point to the same kind of insulation: protection that can come off for service, or that guards a hot surface people can reach. One is the Washington State Energy Code, for outdoor HVAC piping. The other is a set of U.S. Coast Guard rules for hot exhaust and piping on certain vessels.


This article quotes the current official text and describes how a removable cover is built to help meet that requirement. It is not legal advice. Check the current code or regulation with your building official, marine surveyor, or the Coast Guard before you treat any cover as meeting a requirement.


We already published a Seattle-focused post on Coast Guard hot-surface rules https://www.alltempsoftcovers.com/post/seattle-marine-insulation-1. This post is different: it covers the Washington energy code alongside the Coast Guard rules, and it cites the federal text for more than one vessel class.


All Temp Soft Covers has made custom removable insulation covers in Blaine, Washington, since 2015. We manufacture and ship only. We do not install, and we do not certify a building or a vessel. Customers send photos and measurements; the owner walks them through the numbers by phone or video. We ship nationwide, including Alaska.


Washington energy code: protection that comes off within six feet of the equipment


The rule in force today is the 2021 Washington State Energy Code, Commercial Provisions, adopted as chapter 51-11C WAC and effective March 15, 2024. The section is C403.10.3.1, "Protection of piping insulation," in WAC 51-11C-40391 https://app.leg.wa.gov/wac/default.aspx?cite=51-11C-40391:


Piping insulation exposed to weather shall be protected from damage, including that due to sunlight, moisture, physical damage and wind, and shall provide shielding from solar radiation that can cause degradation of the material. Protection shall be removable for no less than six feet from the equipment for maintenance. Adhesive tape shall not be permitted.


That is not a general rule that all insulation must be removable. It applies to HVAC piping insulation exposed to weather. The protective covering has to stand up to sun, moisture, physical damage, and wind, and it has to be removable for no less than six feet from the equipment so maintenance can be done without tearing the insulation apart. Tape is not an accepted form of protection.


A custom removable pipe insulation jacket https://www.alltempsoftcovers.com/removable-pipe-insulation-jackets or valve and flange insulation jacket https://www.alltempsoftcovers.com/valve-flange-insulation-jackets is one way to provide that protection on the first six feet of outdoor piping at a unit, pump, or other piece of equipment. The jacket laces on, comes off when a valve, flange, or fitting needs to be reached, and goes back on. We do not call those jackets "code certified." Your inspector decides whether a given cover meets the section.




Before and after: a diesel generator with a bare overhead muffler and exhaust piping, then the same run covered with gray removable insulation covers

Before (left) and after (right): the same diesel generator exhaust muffler and piping, bare and then covered. This is a generator job, not an outdoor HVAC installation.


Coast Guard rules: insulate or guard hot exhaust within reach


Which part of Title 46 applies depends on the vessel. The sections below share one idea: hot exhaust or piping that people can reach has to be insulated or otherwise guarded. A removable marine exhaust insulation blanket https://www.alltempsoftcovers.com/marine-exhaust-insulation-blankets is one way to do the insulating. It is not "USCG approved," and putting one on does not, by itself, pass a vessel inspection.




Fishing boats at a dock. We build the covers in Blaine, Washington, and ship them to the boat, the yard, or the diesel shop. We do not install.


Towing vessels (Subchapter M). 46 CFR 144.830 https://www.ecfr.gov/current/title-46/chapter-I/subchapter-M/part-144/subpart-H/section-144.830 says: "Each exhaust pipe from an internal combustion engine which is within reach of personnel must be insulated or otherwise guarded to prevent burns." On a new vessel, the same section also requires that pipes carrying vapor, gas, or liquid above 150°F (65.5°C) within reach of personnel "must be insulated where necessary or otherwise guarded to prevent injury."


Small passenger vessels (Subchapter T, under 100 gross tons). 46 CFR 177.970 https://www.ecfr.gov/current/title-46/chapter-I/subchapter-T/part-177/subpart-I/section-177.970 says: "Piping, including valves, pipe fittings and flanges, conveying vapor, gas, or liquid, the temperature of which exceeds 65.5 °C (150 °F), must be suitably insulated where necessary to prevent injuries." 46 CFR 182.430(a) https://www.ecfr.gov/current/title-46/chapter-I/subchapter-T/part-182/subpart-D/section-182.430 adds that exhaust-system protection must be provided in compliance with § 177.970 "at such locations where persons or equipment might come in contact with an exhaust pipe."


Some commercial fishing vessels. 46 CFR 28.215(c) https://www.ecfr.gov/current/title-46/chapter-I/subchapter-C/part-28/subpart-C/section-28.215 uses nearly the same language: "Each exhaust pipe from an internal combustion engine which is within reach of personnel must be insulated or otherwise guarded to prevent burns." Under 46 CFR 28.200 https://www.ecfr.gov/current/title-46/chapter-I/subchapter-C/part-28/subpart-C/section-28.200, that Subpart C rule applies to documented commercial fishing industry vessels that operate beyond the Boundary Lines, operate with more than 16 individuals on board, or are fish tender vessels engaged in the Aleutian trade. It does not automatically apply to every fishing boat.


For the Seattle and Puget Sound angle on the towing-vessel rule, see the Coast Guard hot-surface post https://www.alltempsoftcovers.com/post/seattle-marine-insulation-1. For covers built for boats in this region, see marine insulation covers for Seattle https://www.alltempsoftcovers.com/seattle-marine-insulation-covers.





Before (left) and after (right): a bare marine turbo exhaust elbow, then the same elbow in a gray removable blanket.




Gray removable exhaust blankets on a marine engine riser and elbow, laced closed with stainless wire, next to the turbo.


Why a removable cover fits both rules


The energy code wants the first six feet of outdoor piping protection at the equipment to come off for maintenance, and it does not allow adhesive tape as that protection. A laced jacket is built for that.


The Coast Guard sections above require insulation or a guard on hot exhaust or piping that people can reach. A removable exhaust blanket covers that surface, then unlaces when a mechanic needs the joint, the flex, or the turbo.




Gray removable exhaust blankets on the riser and elbow of a marine diesel, laced with wire and anchors.




Removable blankets on an exhaust elbow and the pipe next to it, split so one section can come off on its own.




An exhaust run covered section by section, so each blanket can come off on its own. Same engine room as the elbow photo above.


For high-temperature exhaust builds, our inner insulation is rated 1,000°F continuous and 1,200°F max, and the gray outer cloth is rated 450°F continuous and 500°F max. Closures are wire lacing and anchors. Tell us the operating temperature and where the part sits, and we will match the build to those ratings before anything is sewn. Lead time depends on the size of the job. We also build generator exhaust insulation blankets https://www.alltempsoftcovers.com/generator-exhaust-insulation-blankets for diesel gensets on shore or on a boat.


How to order


You do not need to bring the equipment to Blaine, and we do not come on site to measure. Send photos of each part from several angles, plus the measurements you have: pipe size or circumference, lengths, cutout centers, and heel and throat on 90° elbows. Our measuring guide https://www.alltempsoftcovers.com/how-to-measure-insulation-covers shows what to measure. The owner goes over the photos and measurements with you by phone or video before we build. We make the covers in Blaine and ship them to you, your yard, or your shop, anywhere in the United States, including Alaska. Your crew, mechanic, or installer puts them on.


Request a free quote https://www.alltempsoftcovers.com/contact-free-quote.


Frequently asked questions


Does the Washington energy code require removable insulation covers?


Section C403.10.3.1 requires that the protection on HVAC piping insulation exposed to weather be removable for no less than six feet from the equipment for maintenance, and it does not permit adhesive tape. A removable jacket is one way to provide that protection. Your building official decides whether a given cover complies.


Are these covers Coast Guard approved or certified to the energy code?


No. We do not sell "USCG approved" or "code certified" covers. We build removable covers to help meet the removable-protection requirement in the energy code and the insulate-or-guard requirement in the Coast Guard sections cited above. Inspection and acceptance are up to your official, surveyor, or the Coast Guard.


Which Coast Guard rule applies to my boat?


It depends on the vessel. Towing vessels are under 46 CFR 144.830. Small passenger vessels under 100 gross tons are under 46 CFR 177.970 and 182.430. The fishing-vessel exhaust rule in 46 CFR 28.215 applies only to the documented vessels described in 46 CFR 28.200. Ask your surveyor or the Coast Guard which part applies to your boat.


Can you build covers if I am not near Blaine?


Yes. Send photos and measurements. The owner walks you through measuring by phone or video. We ship nationwide, including Alaska.


Sources


Official texts verified on November 22, 2026:


• Washington State Energy Code, Commercial Provisions, Section C403.10.3.1 (WAC 51-11C-40391): official WAC https://app.leg.wa.gov/wac/default.aspx?cite=51-11C-40391. Same wording in the official WAC HTML https://lawfilesext.leg.wa.gov/law/WAC/WAC%20%2051%20%20TITLE/WAC%20%2051%20-%2011C%20CHAPTER/WAC%20%2051%20-%2011C-40391.htm. The 2021 WSEC-C, 2nd edition (effective March 15, 2024) is posted by the State Building Code Council https://sbcc.wa.gov/sites/default/files/2024-01/2021_WSEC_C_2ndEd_012824.pdf.

• 46 CFR 177.970: eCFR https://www.ecfr.gov/current/title-46/chapter-I/subchapter-T/part-177/subpart-I/section-177.970.

• 46 CFR 182.430: eCFR https://www.ecfr.gov/current/title-46/chapter-I/subchapter-T/part-182/subpart-D/section-182.430.

• 46 CFR 144.830: eCFR https://www.ecfr.gov/current/title-46/chapter-I/subchapter-M/part-144/subpart-H/section-144.830.

• 46 CFR 28.215 and 28.200: eCFR 28.215 https://www.ecfr.gov/current/title-46/chapter-I/subchapter-C/part-28/subpart-C/section-28.215, eCFR 28.200 https://www.ecfr.gov/current/title-46/chapter-I/subchapter-C/part-28/subpart-C/section-28.200.


This article is not legal advice. Codes and regulations are updated. Read the current official text and check with your inspector or surveyor.


Comments


bottom of page