top of page

Marine Exhaust Insulation for Alaska Boats: Measured Remotely, Shipped to You

Writer: alltempsoftcovers
alltempsoftcovers
6 days ago
3 min read

Updated: 5 days ago

If your boat works in Alaska, getting replacement exhaust insulation can be a project in itself. Local options are limited, the season is short, and nobody wants the boat tied up waiting on parts. The good news is that custom removable exhaust blankets don't require anyone to come to the boat. We build them from photos and measurements, and we ship anywhere in Alaska.

Why Alaska boats need good exhaust insulation

Fishing boats, tenders, workboats and liveaboards in Alaska put their engines through long, hard seasons. That's tough on exhaust insulation:

  • Long run hours mean constant heat cycling.

  • Vibration works loose wrap, tape and wire.

  • Frequent repairs in remote ports mean lagging gets cut off and doesn't always go back on.

  • Tight engine rooms put crews right next to hot exhaust.

Damaged or missing lagging is a burn risk and lets heat pour into the engine room, warming hoses, wiring and fuel lines along the way.

Why removable blankets make sense up north

A removable exhaust blanket is sewn to the shape of a specific part, such as a riser, elbow, muffler, turbo outlet or straight pipe, and closes with fasteners. For a boat in Alaska that means:

  • Your crew can fit it. No installer required. We manufacture the covers and ship them ready to install.

  • It survives service. When a mechanic needs to get at a gasket or a sensor, they open that section and close it back up afterward.

  • Closures that hold. On high-vibration marine engines, stainless lacing wire is the most reliable closure: it won't melt, stretch or shake loose.

  • You can replace one piece. Sections are split at joints, so a single worn cover can be replaced without redoing the whole system.

How the covers are built

Every marine exhaust insulation blanket we make is custom-fabricated in our shop in Blaine, Washington. For high-temperature exhaust builds:

  • Inner insulation: rated 1,000°F continuous (1,200°F max).

  • Gray outer cloth: silicone cloth rated 450°F continuous (500°F max).

  • Hot face: stainless wire mesh against the pipe.

We also make turbo blankets, muffler covers, generator exhaust covers, and covers for piping and valves.

How remote measuring works

This is the part people worry about, and it's simpler than it sounds.

  1. Take photos first. Shoot each section of the exhaust from a few angles, including close-ups of the ends, joints and flanges and the space around each part. Put a tape measure in the shot for scale where you can.

  2. Write down what you know: engine make and model, and any part numbers on risers, elbows, mufflers or the turbo.

  3. Measure the basics: pipe size or circumference, lengths, the heel and throat of each 90° elbow, and the centers of any cutouts. Our measuring guide shows how. Only measure when the engine is cold.

  4. Get on a call. The owner personally walks you through measuring by phone or video, step by step, so everything is right before we build. A video call from the engine room is often the fastest way to sort out a tricky section.

  5. We quote, build and ship to you anywhere in Alaska.

Plan ahead of the season if you can: send photos while the boat is laid up, and the covers can be ready to fit before you head out.

Photo tips that make remote measuring easier

  • Clean the lens and use the flash or a work light. Engine rooms are dark, and dim photos hide edges and joints.

  • Shoot each part straight on, then from the side, so the bend angles show.

  • Number the sections in your notes (riser 1, elbow 2 and so on) and match them to your photos and measurements.

  • Include old covers if you have them, but always measure the bare part.

  • Send everything at once if you can, so nothing gets lost across emails.

FAQ

Do you ship to remote Alaska communities? Yes. We ship anywhere in Alaska, as well as nationwide across the US. Tell us where the boat is when you request a quote.

Can I order just one replacement section? Yes. We build single covers as well as full exhaust systems.

Do you install? No. We manufacture only. Covers ship ready for your crew, mechanic or yard to fit.

Get a quote from Alaska

Send photos and measurements through our free quote form, call 360-383-6857 or email info@alltempsoftcovers.com. Tell us where the boat is and when you need the covers.

All Temp Soft Covers · Custom removable insulation covers · Made in Blaine, WA · Shipping nationwide, including anywhere in Alaska

All Temp Soft Covers logo

Comments


bottom of page