What Is a Marine Exhaust Blanket, and Do You Need One?


A marine exhaust blanket is a removable insulation cover made to fit one part of a boat's exhaust: an elbow, a riser, a manifold, a muffler or a stretch of pipe. It laces closed around the part, stays put while the engine runs, and comes off when somebody needs to get at what's underneath. Then it goes back on.
Quick answer: If you have a hot exhaust in a tight engine room and you expect to work on it again, a marine exhaust blanket is the kind of insulation built for that. Send us photos and measurements. We build it in Blaine, WA, and ship it to you, anywhere in the U.S. including Alaska. You or your mechanic put it on. We manufacture only.
What a marine exhaust blanket covers
On most boats the exhaust is the hottest thing in the engine room. A marine exhaust blanket can be made for:
Exhaust elbows and risers, including wet exhaust parts up to the point where cooling water is injected
Exhaust manifolds
Turbochargers (see marine turbo blankets)
Dry stacks and exhaust piping, including bends, flex sections and flanges
Mufflers and silencers
You can order one blanket for one problem part, or a full set for the engine room. Our marine exhaust insulation blankets page has the full list.

How a marine exhaust blanket is built

Every blanket is made in layers, and the layers depend on how hot the part runs and where it sits:
Hot face: stainless wire mesh against the pipe on high-temperature exhaust builds
Insulation: E-glass needled mat with no chemical binders, rated 1,000°F continuous and 1,200°F max
Outer cloth: gray silicone cloth, rated 450°F continuous and 500°F max
Closure: stainless wire lacing and anchors
Lacing wire is what we use because exhaust vibrates. Wire lacing and anchors hold a blanket on through vibration and let a mechanic open it up when needed.
The outer cloth is rated lower than the insulation under it, as on any layered cover. Tell us how hot the part gets and where it sits, and we'll check the build against the ratings before we make anything.
Why boat owners ask for one
Burn protection. A bare exhaust elbow can burn anyone working near it. For some vessels this is more than a good idea. For towing vessels, 46 CFR 144.830 says each exhaust pipe from an internal combustion engine that is within reach of personnel must be insulated or otherwise guarded to prevent burns. For small passenger vessels, 46 CFR 177.970 says piping, including valves, pipe fittings and flanges, above 150°F (65.5°C) must be suitably insulated where necessary to prevent injuries. Which rules apply to your boat depends on the vessel, so check with your surveyor or the Coast Guard. A blanket is one way to do the insulating. We don't certify a vessel or tell you what it needs to pass.
Heat stays in the exhaust. A covered exhaust puts less heat into the hoses, wiring and fuel lines around it.
Access. Exhaust parts get inspected and serviced. A blanket unlaces, comes off in one piece, and goes back on after the work. The insulation is not destroyed each time somebody needs a look at a joint or gasket.
Fit. The blanket is made to your part, so it follows the bends, flanges and clamps and leaves openings for fittings that have to stay clear.
Marine exhaust blanket vs. exhaust wrap and lagging
People use "lagging" for both wound-on exhaust wrap and sewn covers. The practical difference is what happens on the day you need to open the exhaust. Wrap gets cut or unwound, and it rarely goes back on the way it was. A blanket comes off and goes back on. We wrote that comparison up in Marine Exhaust Blanket vs. Exhaust Wrap. If your current lagging is worn, see Marine Exhaust Lagging: When to Replace It.
Do you need one?
A marine exhaust blanket is likely a good fit if:
crew or mechanics work close to a bare exhaust part
the engine room is cramped and the exhaust is within reach
you have wrap or lagging that is torn, oily or cut away for repairs
you service the exhaust, turbo or muffler regularly and want to reuse the insulation
It is not a fit if the part will never be touched and a simple wrap does the job. We'd rather tell you that than sell you something you don't need.
How to order a marine exhaust blanket
You don't have to bring the boat to us, and there is no site visit.
Send what you have. Photos of the part from a few angles, part numbers or drawings, pipe size or circumference, centers for any cutouts, and the heel and throat on 90° elbows. Include the exhaust or surface temperature if you know it.
Measure with the owner. He walks you through the measuring by phone or video call so every number is right before anything is built. Our measuring guide shows what to measure.
We build it in Blaine, WA. Lead time depends on the size of the job.
We ship it to you, anywhere in the U.S., including Alaska. Your crew, mechanic or boatyard puts it on. We don't install.
Get a free quote, call 360-383-6857, or email info@alltempsoftcovers.com.
Marine exhaust blanket FAQ
What is a marine exhaust blanket?
It is a removable, made-to-measure insulation cover for a boat's exhaust elbow, riser, manifold, muffler or pipe. It laces closed over the part and comes off for service.
Is a marine exhaust blanket the same as marine exhaust lagging?
People use the two terms for the same job. "Lagging" can also mean wound-on wrap. A marine exhaust blanket is the sewn, removable kind, so it can come off and go back on.
Can I get a boat exhaust insulation blanket for just one part?
Yes. We make a single blanket for one elbow or muffler, or a full set for the engine room.
What temperatures can a marine exhaust blanket handle?
Our inner insulation is rated 1,000°F continuous and 1,200°F max. The gray outer cloth is rated 450°F continuous and 500°F max. Tell us how hot your part runs and we'll check the build before we make it.
Do you ship removable marine exhaust insulation to Alaska, and do you install it?
We ship anywhere in the U.S., including Alaska. We don't install. Your crew, mechanic or boatyard puts it on, and the owner walks you through measuring by phone or video before we build it.
Get a marine exhaust blanket quote
All Temp Soft Covers was founded in 2015 and builds removable insulation covers in Blaine, Washington. Send photos of your exhaust and we'll quote it for free.
Phone: 360-383-6857
Email: info@alltempsoftcovers.com
More on this topic: <a href="https://www.alltempsoftcovers.com/marine-exhaust-insulation-blankets">marine exhaust insulation blankets</a> · <a href="https://www.alltempsoftcovers.com/marine-turbo-blankets">marine turbo blankets</a> · <a href="https://www.alltempsoftcovers.com/post/marine-exhaust-blanket-vs-exhaust-wrap">Marine Exhaust Blanket vs. Exhaust Wrap</a>



Comments